PRODUCTS>> Waterproofing Coating

 
/map>


WALL-NUT ! High performance, 100% acrylic exterior coating. A coating formulated with special dust proof, anti-fungus and powerful weather proof features. Available in an imaginative variety of attractive shades. Features which ensure that every coat of Wall-Nut, forms a durable and protective exterior coating while adding to the aesthetic appeal of every structure. It is easy to handle and apply plus the value for money. This makes Wall-Nut the first choice for imaginative, yet durable exterior coatings.

Attractive Colour Coating
+ Superb Dirt Pick Resistance

 

 



Technical Information

Characteristics
 Nature
:
 One component, water thinnable
 Thinner
:

 Municipal or potable water
(1 Lit Wall-Nut + 400 ml water)
 Drying Time
:

Dry to touch - 30 minutes
 Recoating Period
:

 Minimum 6 hours at room temperature (Ideally 24 hours)
 Dry film thickness
:
 25-30 Microns per coat
 Finish
:
 Smooth and Matt
 Shades
:
 As per shade card

 Method of Application
:
 By Brush, Roller and Airless spray
 Recommended coats
:
 2-3 depending on the substrate and DFT
 Adhesion on Concrete
:
 Good
 Coverage (per ltr/2 coat)
  - Bare Concrete
  - Asbestos Panel
  - Sealer Coat
  - White Cement Slurry
  (1:1 dilution with water) 		  50 sq.ft
80 sq.ft.
67 sq.ft.
61 sq.ft.


Features / Advantages
  • Superb resistance to dirt pick-up for an attractive appearance.
  • Resistance to chalking and flaking.
  • Waterborne chemistry for uncomplicated handling and dean up.
  • Highly durable & Ultra Violet resistant.
  • Excellent anti-fungal and anti-algal properties.
  • Weatherproof.
  • Available in attractive shades.


Typical Application

  • Exterior R.C.C. surface
  • Masonry walls / facades.
  • Asbestos sheets


Direction for use

Adequate surface preparation as given below is necessary for product performance.

New Masonry - Wall-Nut should not be applied to concrete and to other surfaces less than seven days old. Ideally concrete should be allowed to cure for 28 days before application. Power wash to ensure no under bound sand or cement remains on the surface.


Existing Masonry

  • The substrate should be free from CHALKING.
  • All dust, grease, loose paint, powdery particles, fungus and algae need to be completely removed from the walls.
  • Apply BIOWASH on the walls to remove remaining traces of fungi/algae
    and allow it to stand for one hour. Clean the walls after 1 hour with water
    jet to remove the BIOWASH applied and wait for 1 hour.
  • Fill any existing cracks upto 3 mm with PAINTEX-Acrylic Crack Filling
    Compound     - Paintable sealant.
  • Cracks of more than 3 mm with POLYSULPHIDE SEALANT. For ferrous
    substrate, apply an undercoat of Anti-corrosive primer, CHOKSEY’S TECHGAURD 101 Or Coaltar-Epoxy.

FOR WATERPROOFING CHARACTERISTICS, ONE COAT OF FUTURA-5 (Elastomeric Waterproofing Coating) CAN BE APPLIED BEFORE 2 COATS OF WALLNUT.



Application
WALL-NUT can be applied by airless spray, roller or brush. The material is to be
diluted with specified amount of water ( 1 Litre Wallnut : 400 ml water). Apply the
first coat at the spread rate of 50-60sq.ft/lt/coat. Allow it to dry for minimum 6
hours (preferably 24 hours) before application of second coat. Apply second coat
of WALL-NUT at the spread rate of 70-75 sq.ft/lt/coat.


Precautions

  • Do not over-thin WALL-NUT
  • Not exceeding given amount of water)
  • Do not over-extend the brush.

Storage And Shelf Life
18 months in original packing, if stored at room temperature i.e. 20°C - 35°C.


Packing:
1 Litre, 4 Litres & 20 Litres

 



 
Home l Profile l Projects l Products l Services l Branches l Credentials l Recognition l R&D l Clients l Global Partners l Exports l Contact us

© Choksey Chemicals Pvt. Ltd. - Corporate Communication. All rights reserved