|
FEATURES / ADVANTAGES
- It provides dust free, seamless
floor which is extremely easy to
clean.
- Good abrasion resistance withstands
foot and light vehicular traffic.
- Excellent in chemical resistance.
- Available in a wide range of
colours to provide a very attractive
floor finish.
- Solvent free system and it can
be laid easily and quickly
TYPICAL APPLICATION
- Mainly used on floor, where high
degree of cleanliness and hygiene
are
required.
- Can be used for hospital clean
rooms, electronic assembly areas,
food and chemical plant,
- Slaughter houses and distilleries.
TYPICAL CHARACTERISTICS
Nature
|
:
|
Four Component |
Colour
|
: |
Light grey,
dark grey, light green, light
blue. etc.
Colours can be provided as per
the specifications
if so required. |
| Mixing
ratio, part by weight |
:
|
Part I: Part
II: Part
III:
Part IV:
(Base) (Hardener)
( Filler ) (Pigment
Paste)
8 5
20
1 |
Pot
life at 30°C |
: |
30 minutes |
| Initial
cure at 30°C (light foot traffic) |
: |
24
hours |
| Total
Curing time at 30°C. |
: |
6 days |
ENGINEERING DATA :
|
|
|
|
Specification Complies |
: |
British Standard
Specification, BS - 6319 |
|
Flexural Strength, Kg/cm²
|
: |
350 |
| Tensile
Strength, Kg/cm² |
: |
180 |
| Impact
Resistance, Kg/cm² |
: |
5
To 6 |
| Abrasion
Resistance, mm |
: |
2 |
| Compressive
Strength, Kg/cm² |
: |
500 |
DIRECTIONS
FOR USE
SURFACE, PREPARATION
New concrete or cementitious substrates
should have been placed for at least
28 days and have moisture content
of less than 5% before topping with
Techfloor SL-2. .
All substrates should be sound and
free from contamination such as mortar
and paint splashes, curing compound
residue oil & grease. Excessive
latence should be removed by light
mechanical scabbling grinding or grit
blasting. Light laitance may be removed
by acid etching with Masterklean AEA
followed by Masterklean DGA (Degreasing
agent) followed by thorough washing
with clean water and then allowing
the surface to dry.
MIXING
Techftoor SL- 2 is supplied in pre-weighed
packs ready to use on site. Do not
add solvent or thinner, though mixing
is essential. Mix Part II & Part
I in their individual containers homogeneously.
Hold Mix of Part I and Part II under
a mechanical stirrer till a homogenous,
even mix is obtained. Add part IV
followed by part III filler part under
stirring to get homogenous mix.
LAYING
The material is poured on to the substrate
and spread to the required thickness
with a steel trowel,
Immediately after spreading the floor
should be timely rolled using special
spiked roller.
CLEANING
Tools and equipment should be cleaned
with solvents like xylene, acetone
etc. immediately.
COVERAGE
Typically at 2 mm thickness - 17 Kg
pack covers - 5m² area
STORAGE AND SHELF LIFE
Sealed packs have a shelf life of
12 months when stored in ware house
conditions below 35°C. and 50%
R.H.
PACKING: 8.5 Kg
and 17 Kg
PRECAUTIONS
- If mixed resin comes in contact
with skin, it must be removed before
it
hardens with a resin removing cream
followed by washing with soap and
water, do not use solvent.
- If an accidental eye contamination
occurs with any of the above products,
wash well with plenty of clean water
and seek medical advice.
|
